Siemens Synco living Operating Instructions Manual Download Page 46

Page: 46 / 100

46 / 100

Siemens

Synco™ living Operating instructions

CE1B2707en

Building Technologies

Central apartment unit QAX910

23.08.2008

State

Displays the current ventilation operating mode (Comfort, Precomfort, Econ-
omy, Protection).

Main menu > Ventilation > Operating mode > State:

Reason

Displays the reason for the current ventilation operating mode (state).

Possible reasons:

•

Commissioning

•

Absence

•

Holidays

•

Time switch

•

Apartment operating mode

•

Operating mode contact

•

Apartment timer

•

Special day

Main menu > Ventilation > Operating mode > Cause:

Operating mode for absence

The desired ventilation operating mode for absence (see page 27) is set via
the following operating line.

Main menu > Ventilation > Operating mode > Optg mode absence:

Factory setting

---

Setting

--- (no operating mode changeover)

Comfort

Precomfort

Economy

Protection

Changeover of the ventilation operating mode occurs only if the venti-
lation operating mode for absence is below that for normal operation.

The setting for the ventilation mode for absence does not depend on
the setting for room operating mode for absence. However, both
operating modes can be changed over via the absence button.

Summary of Contents for Synco living





































































































Search results

Summary of Contents for Synco living

Reviews:

Related manuals for Synco living

Brands by name

Popular brands

Siemens Synco living, Operating Instructions Manual

Search results

Summary of Contents for Synco living

Reviews:

Related manuals for Synco living

Brands by name

Popular brands