Siemens Synco living Operating Instructions Manual Download Page 9

Page: 9 / 100

9 / 100

Siemens

Synco™ living Operating instructions

CE1B2707en

Building Technologies

Safety notes

23.08.2008

Safety notes

Product liability

•

Use these products only in building services plant and only for the

applications described.

•

Comply with all local safety regulations (installation, etc.).

•

Do not open the devices. Opening the devices will void warranty by

Siemens.

•

If a device is defective or damaged, disconnect it from power

immediately and replace it.

•

Application-related technical data are only guaranteed in connec-

tion with the Siemens Synco™ living system. When using together
with third-party products not specified by Siemens, user must en-
sure functionality. In that case, Siemens does not provide any ser-
vices or warranty.

Summary of Contents for Synco living





































































































Search results

Summary of Contents for Synco living

Reviews:

Related manuals for Synco living

Brands by name

Popular brands

Siemens Synco living, Operating Instructions Manual

Search results

Summary of Contents for Synco living

Reviews:

Related manuals for Synco living

Brands by name

Popular brands