Siemens Synco living Operating Instructions Manual Download Page 72

Page: 72 / 100

72 / 100

Siemens

Synco™ living Operating instructions

CE1B2707en

Building Technologies

Central apartment unit QAX910

23.08.2008

Inputs / Outputs

Inputs

Displaying input signals

The current input signals can be displayed via the following operating line:

Main menu > Inputs / Outputs > Inputs > …

The following values – if available – are displayed:

•

Actual value of the outside temperature

•

Outside temperature mixed

•

Outside temperature attenuated

•

Operating mode contact

•

Summer mode

•

H/C changeover

•

Absence

•

Twilight

•

Fault input X (per fault input 1 - 8)

Outputs

Displaying output states

The states of the outputs can be displayed via the following operating line:

Main menu > Inputs / Outputs > Outputs > …

The following values – if available – are displayed:

•

Switching group X (relay per switching group 1 - 8)

•

Fault output X (per fault output 1 and 2)

•

Heat demand relay

•

Heat demand DC 0..10 V

•

Summer operation

•

Status output

•

Window / door state

•

Exhaust hood

Summary of Contents for Synco living





































































































Search results

Summary of Contents for Synco living

Reviews:

Related manuals for Synco living

Brands by name

Popular brands

Siemens Synco living, Operating Instructions Manual

Search results

Summary of Contents for Synco living

Reviews:

Related manuals for Synco living

Brands by name

Popular brands