manualshive.com logo in svg

Siemens Synco living, Operating Instructions Manual, Page: 79 / 100

Share
Download
Siemens Synco living Operating Instructions Manual Download Page 79

 

79 / 100 

Siemens 

Synco™ living Operating instructions 

CE1B2707en 

Building Technologies 

Central apartment unit QAX910 

23.08.2008 

Door names 1 - 2 

 

Assign a meaningful name to the doors, e.g. entry door, garage door, etc. 

 

Main menu > Settings > Texts > Doors > Door X: 

 

Lamp names 1 – 4  

 

Assign the lamps self-explanatory names, e.g. Living, Eating, etc.: 

 

Main menu > Settings > Text > Light state > Lamp X: 

 

Name for temperatures 1 - 3 

 

Assign meaningful names to the temperatures, e.g. basement, swimming 
pool, etc. 

 

Main menu > Settings > Texts > Temperature display  
> Temperature X: 

 

Device information 

 

Info lines 

 

The central apartment unit provides information for readout: 

Main menu > Device information > Plant name: 

Main menu > Device information > File name: 

Main menu > Device information > Device type: 

Main menu > Device information > Software version: 

Main menu > Device information > Hardware version: 

 

 

Summary of Contents for Synco living





































































































Reviews:

No comments