Siemens Synco living Operating Instructions Manual Download Page 50

Page: 50 / 100

50 / 100

Siemens

Synco™ living Operating instructions

CE1B2707en

Building Technologies

Central apartment unit QAX910

23.08.2008

Open fireplace mode

Shows if ventilation was switched via external contact to open fireplace opera-
tion (Off, On).

Main menu > Ventilation > Ventilation state > Fireplace mode:

Ventilation contacts

Shows the current state of the two ventilation contacts (Off, On).

Main menu > Ventilation > Ventilation state > Ventilation contact1:

Main menu > Ventilation > Ventilation state > Ventilation contact2:

Service

Service interval

Specify after how many hours (0..99,999) ventilation needs service (e.g.
change air filter). The central apartment unit shows a corresponding message
when the set number of hours is reached.

Setting 0 h means that the service interval and the associated mes-
sage are disabled.

Main menu > Ventilation > Service > Service interval:

Factory setting

0 h

Setting

Operating hours since maintenance

Shows the number of ventilation operating hours since last maintenance.

The operating hours must be reset to 0 to delete the service message.

The operating hours since service can be set to 0 or any value.

Main menu > Ventilation > Service > O’hrs since service:

Summary of Contents for Synco living





































































































Search results

Summary of Contents for Synco living

Reviews:

Related manuals for Synco living

Brands by name

Popular brands

Siemens Synco living, Operating Instructions Manual

Search results

Summary of Contents for Synco living

Reviews:

Related manuals for Synco living

Brands by name

Popular brands