Siemens Synco living Operating Instructions Manual Download Page 19

Page: 19 / 100

19 / 100

Siemens

Synco™ living Operating instructions

CE1B2707en

Building Technologies

Central apartment unit QAX910

23.08.2008

Arrow up

button

For navigating upward within a menu level, for scrolling backward on
the info pages, and for setting (increasing) values.

Arrow down

button

For navigating downward within a menu level, for scrolling forward
on the info pages, and for setting (decreasing) values.

Esc

button

For navigating backward to the next higher menu level, for quitting
the main menu, and for canceling entry of a value.

Menu / ok

button

For entering the main menu, for navigating to a lower menu level,
and for confirming entry of a value.

Pair of softkeys 1 - 4

For triggering the switching group functions defined during commis-
sioning (e.g. switching or dimming lights), or for calling up predefined
info pages.

1A, 1B

Softkeys 1A and 1B

2A, 2B

Softkeys 2A and 2B

3A, 3B

Softkeys 3A and 3B

4A, 4B

Softkeys 4A and 4B

Summary of Contents for Synco living





































































































Search results

Summary of Contents for Synco living

Reviews:

Related manuals for Synco living

Brands by name

Popular brands

Siemens Synco living, Operating Instructions Manual

Search results

Summary of Contents for Synco living

Reviews:

Related manuals for Synco living

Brands by name

Popular brands