Siemens Synco living Operating Instructions Manual Download Page 38

Page: 38 / 100

38 / 100

Siemens

Synco™ living Operating instructions

CE1B2707en

Building Technologies

Central apartment unit QAX910

23.08.2008

Copying switching times

When you scroll to the end of the switching point list, option “Copy to:“ will
appear.

Monday

Copy to:

You can copy the switching times of
the respective day to any other
weekday (including the special day)
or to a number of weekdays (Mo – Fr
or Mo – Su).

Setting new switching points

For every weekday and the special day, you can set and define up to 6 switch-
ing points where the room temperature setpoint should change.

Monday

- - : - - - - - - - -

To define a new switching point,
press the

Arrow down

button until

an empty switching point appears
(--:--, after the existing switching
points). Now, press the

Menu / ok

button.

Monday

From 06:00

Comf

Use the

Navigation

buttons to set a

value between 00:00 and 23:59.
Confirm the setting with the

Menu / ok

button.

Monday

From 06:00

Comf

Now, adjust the room temperature
setpoint (Comfort, Precomfort or
Economy) that should apply after this
switching time.

Monday

From 06:00

Comf

To complete the setting, press again
the

Menu / ok

button. The display

returns to the menu.

Adapting and deleting switching points

Monday

From 06:00

Comf

To change an existing switching
point, select it with the

Arrow

buttons

and then press the

Menu / ok

button. Use the

Arrow

buttons to change the value.

06:00

Comf

06:00

Summary of Contents for Synco living





































































































Search results

Summary of Contents for Synco living

Reviews:

Related manuals for Synco living

Brands by name

Popular brands

Siemens Synco living, Operating Instructions Manual

Search results

Summary of Contents for Synco living

Reviews:

Related manuals for Synco living

Brands by name

Popular brands