Siemens Synco living Operating Instructions Manual Download Page 70 | Manualshive

Page: 70 / 100

background image

70 / 100

Siemens

Synco™ living Operating instructions

CE1B2707en

Building Technologies

Central apartment unit QAX910

23.08.2008

Holiday operating mode

Apartment operating mode during holidays

Select the required operating mode for the apartment during the holiday pe-
riod. The apartment operating mode during holidays applies to heating / cool-
ing and ventilation.

To be able to release cooling in holiday mode, the air conditioning
release mode shouldn't be set higher than the apartment operating
mode during holidays (see page 35).

Main menu > Holidays/special days > Ap optg mode holid:

Guide value

Economy

Your setting

Economy

Protection

DHW operating mode during holidays

Select the required DHW operating mode for the holiday period or the special
day:

Main menu > Holidays/special days > DHW optg mode holid:

Guide value

Protection

Your setting

--- (no impact)

Normal

Reduced,

Protection

Time settings

Date / time of day

You can make the settings for the date and the time of day by using the fol-
lowing paths:

Main menu > Time of day/date > Time of day:

Main menu > Time of day/date > Date:

Main menu > Time of day/date > Year:

«
...
68
69
70
71
72
...
»

Summary of Contents for Synco living





































































































Reviews:

No comments

Related manuals for Synco living

Brand: Rayrun Pages: 2

Brand: IDenticard Pages: 2

Brand: 3Ware Pages: 2

Brand: Parasound Pages: 72

Brand: Jafar Pages: 15

Brand: Waters Pages: 55

Brand: Paradox Pages: 2

Brand: GANTERUD Pages: 24

SolarCell Remote

Brand: Samsung Pages: 2

Brand: Samsung Pages: 20

Brand: Danfoss Pages: 37

Brand: Daikin Pages: 44

Brand: DayTronic Pages: 22

Brand: DayTronic Pages: 414

Brand: Hama Pages: 7

Brand: Hama Pages: 44

Brand: RadioMaster Pages: 10

Brand: K&K Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands