Siemens Synco living Operating Instructions Manual Download Page 22

Page: 22 / 100

22 / 100

Siemens

Synco™ living Operating instructions

CE1B2707en

Building Technologies

Central apartment unit QAX910

23.08.2008

Supervision

Door open

Window open

Flashing: Supervised door

opened

Flashing: Supervised window
opened

Windows / doors
Partly monitored

Windows / doors
All monitored

Temperatures, atmospheric pressure and weather trend

Room temperature

Atmospheric pressure steady

Outside temperature

Atmospheric pressure rising

Weather trend: Sunny

Atmospheric pressure
strongly rising

Weather trend: Partly

cloudy

Atmospheric pressure falling

Weather trend: Rainy

Atmospheric pressure
strongly falling

The symbols used for the weather trend only indicate the direction in
which the weather will change. For reliable weather trends, the alti-
tude of the location must be entered at the service level.

Assignment of softkeys

Switching group on

Light on / brighter

Switching group off

Light off / darker

Scene

Blinds opening

Selection of info pages

Blinds closing

Device directory

Device in order

Device faulty

Battery low

Menu levels

Main menu

Holidays / special days

Apartment

Time of day / date

Rooms

Faults

Room groups

Inputs / outputs

Ventilation

Settings

DHW

Device information

Switching groups

Data backup

Supervision

Commissioning

Access levels

Service level

Expert level

Summary of Contents for Synco living





































































































Search results

Summary of Contents for Synco living

Reviews:

Related manuals for Synco living

Brands by name

Popular brands

Siemens Synco living, Operating Instructions Manual

Search results

Summary of Contents for Synco living

Reviews:

Related manuals for Synco living

Brands by name

Popular brands