manualshive.com logo in svg

Siemens SIREMOBIL Iso-C, Service Instructions Manual, Page: 99 / 128

Share
Download
Siemens SIREMOBIL Iso-C Service Instructions Manual Download Page 99

Replacing boards / replacing components

6 - 33

Siemens AG

 

SPR2-230.061.01

Page 33 of 48

SIREMOBIL Iso-C

Medical Solutions

Rev. 13

12.04

CS PS 24

System Manual

 

•

Configure the following parameters in User setup for MEMOSKOP

:

•

Perform the IQ quick test.

Roadmap K-Factor, phase B Program "MD 2". 

Program a different value only upon customer request. 

Roadmap K-Factor, phase C Program "MD 2".

Program a different value only upon customer request. 

Roadmap Time of phase A

Program "4,5". 
Program a different value only upon customer request.

Operating mode Parameters Change the programmed parameters only upon customer 

request.

VCR output

Configure to monitor A.

Hardcopy Release

For SIREMOBIL with 1 monitor: configure to monitor A.
For SIREMOBIL with 2 monitors: Configure to monitor B.

Text monitor

For SIREMOBIL with 1 monitor: configure to monitor A.
For SIREMOBIL with 2 monitors: 
configure to both monitors.

Split screen

Configure horizontally.
Configure vertically only upon customer request.

Display of time

Configure Yes.

Set Date Time

Set the current date and time.

Hospital Name

Program the hospital name.

Storage of Dose on disk

If area dose product meter is present, (Diamentor) con-
figure Yes. Otherwise configure No.

Dose on Hardcopy output

If area dose product meter is present, (Diamentor) con-
figure yes. Otherwise configure No.

With present System MODULARIS the parameters for the Litho-
program have to be set again according the Service instructions 
LITHOSTAR MODULARIS.

NOTE

Summary of Contents for SIREMOBIL Iso-C

































































































































Reviews:

No comments