Siemens SIREMOBIL Iso-C Service Instructions Manual Download Page 57

Page: 57 / 128

Adjustments / Programs

5 - 21

Siemens AG

SPR2-230.061.01

Page 21 of 30

SIREMOBIL Iso-C

Medical Solutions

Rev. 13

12.04

CS PS 24

System Manual

Calibrating the area dose product measurement device

CONSTANT parameter (Qt * Kg) = T

•

Read and record the

value shown on the electronics unit of the area dose product

measurement device.

Programming

•

Connect the service PC to the serial interface of the SIREMOBIL Iso-C.

•

Start the service program.

•

Select the Adjustment, Parameter menu.

•

In the Combo box "Parameter Groups:", select "Diamentor" .

•

Click on "Get from Unit".

•

The Parameter "1. Diamentor Existing" must be on YES .

•

Select parameter "2. Constant (Qt * Kg)" .

•

In "Value Actual:"field, enter the parameter

•

Click on "Set Value".

•

Click on "Put to Unit" .

•

Click on "Save to File".

Fig. 6

This adjustment is used to calibrate the area dose pro

duct mea-

surement device of the SIREMOBIL Iso-C display.

You must exit the service program with "Logoff" and "Quit" to
store the modified parameters to disk as a new file.

Potentiometer

NOTE

Summary of Contents for SIREMOBIL Iso-C

































































































































Search results

Summary of Contents for SIREMOBIL Iso-C

Reviews:

Siemens SIREMOBIL Iso-C, Service Instructions Manual, Page: 57 / 128

Search results

Summary of Contents for SIREMOBIL Iso-C

Reviews: