Siemens SIREMOBIL Iso-C Service Instructions Manual Download Page 12 | Manualshive

Page: 12 / 128

Siemens SIREMOBIL Iso-C Service Instructions Manual Download Page 12

SIREMOBIL Iso-C

SPR2-230.061.01

Page 4 of 18

Siemens AG

System Manual

Rev. 13

12.04

CS PS 24

Medical Solutions

1 - 4

Prerequisites

Danger of infection with pathogens!

Noncompliance can lead to death or physical injury.
This product has been released for operation in operating rooms,
and may therefore be contaminated with infectious blood or other
excreta.
Any skin contact with blood or other excreta must be avoided!
For this reason, you must strictly adhere to the preventive mea-
sures specified in ARTD-002.731.37... !

X-ray radiation!
Noncompliance can lead to illnesses, irreversible damage to body
cells and the genotype, severe injuries and even death.

In work on the system in which radiation must be released, the
radiation protection directives and the rules for radiation protec-
tion according to ARTD-002.731.02 must be complied with.

Note:

- Use available radiation protection devices.
- Wear radiation protection clothing (lead apron).
- Keep your distance from the radiation source as large as pos-

sible.

- Release radiation only if necessary.
- Set the radiation activity as low as possible.

(low kV and mA values, short radiation time)

- Release radiation for as short a time as possible.

Checks in which radiation must be released are identified by the
radiation warning symbol.

WARNING

WARNING

«
...
10
11
12
13
14
...
»

Summary of Contents for SIREMOBIL Iso-C

































































































































Reviews:

No comments