manualshive.com logo in svg

Siemens SIREMOBIL Iso-C, Service Instructions Manual, Page: 105 / 128

Share
Download
Siemens SIREMOBIL Iso-C Service Instructions Manual Download Page 105

Replacing boards / replacing components

6 - 39

Siemens AG

 

SPR2-230.061.01

Page 39 of 48

SIREMOBIL Iso-C

Medical Solutions

Rev. 13

12.04

CS PS 24

System Manual

 

SIMOMED HM monitor 

6

•

Switch the system off.

•

Replace the monitor.

•

Perform the monitor settings as described in the Startup Instructions, Chapter 8.

•

Perform the IQ quick test.

3D reconstruction

 

system electronics 

6

•

The 3D reconstruction system electronics (PC boards D200 incl. MCB300 and D10) is 
attached in front of PC board D1 in the basic unit (Fig. 13).

•

Switch the system off.

•

Unplug all connectors.

•

Replace the module.

•

Reconnect all connectors. 

•

Fasten the shielded cables in the shield connectors again, ensuring good ground con-
tact of the shielding. 

•

If cable ties have been removed, attach the cables with cable ties again. 

•

Perform a download of the control software as described in the Startup Instructions, 
Chapter 5.

•

Perform the mechanical settings as described in the Startup Instructions, Chapter 6.

•

Perform chapters 10 and 11 of the IQ quick test.

Fig. 13

Only applies to SIREMOBIL Iso-C 3D.

Only applies to SIREMOBIL Iso-C 3D.

NOTE

NOTE

Summary of Contents for SIREMOBIL Iso-C

































































































































Reviews:

No comments