manualshive.com logo in svg

Siemens SIREMOBIL Iso-C, Service Instructions Manual, Page: 95 / 128

Share
Download
Siemens SIREMOBIL Iso-C Service Instructions Manual Download Page 95

Replacing boards / replacing components

6 - 29

Siemens AG

 

SPR2-230.061.01

Page 29 of 48

SIREMOBIL Iso-C

Medical Solutions

Rev. 13

12.04

CS PS 24

System Manual

 

MEMOSKOP C / MEMOSKOP C & MOD

6

•

Replace the MEMOSKOP .
The attachment screws are accessible on the underside of the storage device.

•

Check the software status of the MEMOSKOP. Download the system software to the 
MEMOSKOP if necessary.

•

Use the MEMOSKOP Service Software to import the language file.

•

Set the MEMOSKOP C to the correct video frequency and configure it for the number of 
existing monitors.
Refer to chapter 5 "Configuring the video frequency " and "MEMOSKOP - Configuration 
for the number of existing monitors ."

•

Configure the following parameters in Technical Setup for MEMOSKOP:

Check the software status of the newly delivered MEMOSKOP. 
If the software status of the MEMOSKOP differs from that of the 
system, the system software status must be downloaded to the 
MEMOSKOP. 
The MEMOSKOP software status can be read out in the 2nd line 
of the User Setup. 
The first number describes the MEMOSKOP type. 
(2=CE; 3= CE-100/ C/ C & MOD; 4=C-SUB/ C-SUB & MOD).

Read and record the parameters for MEMOSKOP if you can select 
User setup. After replacing the MEMOSKOP, configure the 
MEMOSKOP according to the parameters noted.

Number of Monitors

Configure 1 for SIREMOBIL with 1 monitor.
Configure 2 for SIREMOBIL with 2 monitors.

Hardcopy 

Check whether 5000 is programmed in "4 Max Hardcopy 
time". If not, program this value.

Edge 1 coef set

Check whether 3 is programmed, If not, program this value.

Edge 2 coef set

Check whether 8 is programmed, If not, program this value.

Motion detection setup

Check whether the following are programmed "MD1: 
Threshold" 100 and for "MD2: Threshold" 120. If not, pro-
gram these values.

Date / Time format

Set the country-specific format.

Keyboard

Set to the keyboard layout being used.

Language

Set for language of the country.

Display of realtime clock

Configure Yes. Select No only upon customer request.

Display of rotated images

Configure Yes.

Monitor zoom

Configure No.

Monitor split

Configure Yes.

Monitor text

Configure Yes.

Maximum image number

Configure 700.

NOTE

NOTE

Summary of Contents for SIREMOBIL Iso-C

































































































































Reviews:

No comments