manualshive.com logo in svg

Siemens SIREMOBIL Iso-C, Service Instructions Manual, Page: 97 / 128

Share
Download
Siemens SIREMOBIL Iso-C Service Instructions Manual Download Page 97

Replacing boards / replacing components

6 - 31

Siemens AG

 

SPR2-230.061.01

Page 31 of 48

SIREMOBIL Iso-C

Medical Solutions

Rev. 13

12.04

CS PS 24

System Manual

 

•

Perform the IQ quick test.

MEMOSKOP C-SUB / MEMOSKOP C-SUB & MOD

6

•

Check the software status of the MEMOSKOP. Download the system software to the 
MEMOSKOP if necessary.

•

Use the MEMOSKOP Service Software to import the language file.

•

Replace the MEMOSKOP C-SUB.
The attachment screws are accessible on the underside of the storage device.

•

Set the MEMOSKOP C-SUB to the correct video frequency and configure it for the num-
ber of existing monitors.
Refer to chapter 5 "Configuring the video frequency " and "MEMOSKOP - Configuration 
for the number of existing monitors ."

•

Configure the following parameters in Technical Setup for Memoskop:

Dose on Hardcopy output

If area dose product meter is present, (Diamentor) 
configure yes. Otherwise configure No.

With present System MODULARIS the parameters for the Litho-
program have to be set again according the Service instructions 
LITHOSTAR MODULARIS.

Check the software status of the newly delivered MEMOSKOP.
If the software status of the MEMOSKOP differs from that of the 
system, the system software status must be downloaded to the 
MEMOSKOP. 
The MEMOSKOP software status can be read out in the 2nd line 
of the User Setup. 
The first number describes the MEMOSKOP type. 
(2=CE; 3= CE-100/ C/ C & MOD; 4=C-SUB/ C-SUB & MOD).

Read and record the parameters for MEMOSKOP C-SUB if you 
can select User setup. After replacing the MEMOSKOP C-SUB, 
according to the parameters recorded.

Number of Monitors

Configure 1 for SIREMOBILwith 1 monitor.
Configure 2 for SIREMOBIL with 2 monitors.

Hardcopy 

Check whether 5000 is programmed in "4 Max Hardcopy 
time". If not, program this value.

Edge 1 coef set

Check whether 3 is programmed, If not, program this value.

Edge 2 coef set

Check whether 8 is programmed, If not, program this value.

Motion detection setup

Check whether the following are programmed "MD1: 
Threshold" 100 and for "MD2: Threshold" 120. If not, pro-
gram these values.

Date / Time format

Set the country-specific format.

Keyboard

Set to the keyboard layout being used.

NOTE

NOTE

NOTE

Summary of Contents for SIREMOBIL Iso-C

































































































































Reviews:

No comments