manualshive.com logo in svg

Siemens SIREMOBIL Iso-C, Service Instructions Manual, Page: 29 / 128

Share
Download
Siemens SIREMOBIL Iso-C Service Instructions Manual Download Page 29

3 - 1

Siemens AG

 

SPR2-230.061.01

Page 1 of 2

SIREMOBIL Iso-C

Medical Solutions

Rev. 13

12.04

CS PS 24

System Manual

 

Checking the operating voltages

3

Low voltages

3

Check the operating voltages for the SIREMOBIL Iso-C against the values in table 1.

I.I. Voltages

3

The voltages E1 / E2 / E3 and A may be taken from the I.I. test protocol and checked or 
adjusted against the control test points listed in table 2.

from test point

to test point

Voltage

Potentiometer

D1.X31 (0V)

D1.X30 (+5 V)

+ 5.0 V to

5.2 V

M14. +5 V/Adj.

D1.X34 (0V)

D1.X32 (+15 V)

+ 14.9 V to

15.1 V

M14. +15 V/Adj.

D1.X34 (0V)

D1.X33 (-15 V)

- 14.8 V to 

- 15.2 V

M14. -15 V/Adj.

D30.X1.8 (0V)

D30.X1.9 (+24 V)

+ 24.0 V to

29.6 V

not adjustable

D30.X21.1 (0V) D30.X21.10 (+24 V)

+ 22.8 V to

+ 29.5 V

not adjustable

D30.X20.1 (0V)

D30.X20.3 (+27 V)

+ 27.3 V to

+ 27.8 V

D30 R115

M13.S- (0V)

M13.S+ (+13 V)

+ 13.1 V to

13.3 V

M13.TR1

Tab. 1

Voltage

Test point

Ground 

point

(0V)

Potentiome-

ter for full 

format

Potentiome-
ter for zoom 

format

Voltage

divider

ratio

E1

UE1

P10

P11

1:1

E2

UE2

P6

P7

1:1

E3

UI 15

P2

P3

1:10000

30 kV, Anode

UI 30

P1

P1

1:10000

Tab. 2

Summary of Contents for SIREMOBIL Iso-C

































































































































Reviews:

No comments