manualshive.com logo in svg

Siemens SIREMOBIL Iso-C, Service Instructions Manual, Page: 93 / 128

Share
Download
Siemens SIREMOBIL Iso-C Service Instructions Manual Download Page 93

Replacing boards / replacing components

6 - 27

Siemens AG

 

SPR2-230.061.01

Page 27 of 48

SIREMOBIL Iso-C

Medical Solutions

Rev. 13

12.04

CS PS 24

System Manual

 

•

Configure the following parameters in User setup for MEMOSKOP:

Monitor zoom

Configure No.

Monitor split

Configure Yes.

Monitor text

Configure Yes.

Maximum image number

Configure 100.

Disable doserate selection 
in user setup

Set to "No" when equipped with an area dose product mea-
surement device. The menu "Storage of Dose on disk" and 
the menu "Dose on Hardcopy output" in User Setup are visi-
ble. Otherwise set to "Yes".

Unit serial number

Program the serial number of the SIREMOBIL. 
Do not enter the leading zero. 

Product name

Program "SIREMOBIL Iso-C".

Default program change-
able

Default: Yes.
Depending on country specific regulations configure Yes or 
No.

Create external disk

Configure No.

Default LUT

Configure 2. Program a different LUT curve only upon cus-
tomers request.

Default Edge

Configure 1. Program a different Edge enhancement value 
only upon customers request.

Software backward com-
patible

Configure No.

Operating mode Para-
meters

Change the programmed parameters only upon customer 
request.

VCR output

Configure to monitor A.

Hardcopy Release

For SIREMOBIL with 1 monitor: configure to monitor A.
For SIREMOBIL with 2 monitors: Configure to monitor B.

Text monitor

For SIREMOBIL with 1 monitor: configure to monitor A.
For SIREMOBIL with 2 monitors: configure to both monitors.

Split screen

Configure horizontally. Configure vertically only upon cus-
tomer request.

Display of time

Configure Yes.

Set Date Time

Set the current date and time.

Hospital Name

Program the hospital name.

Storage of Dose on disk

If area dose product meter is present, (Diamentor) con-
figure Yes. Otherwise configure No.

Dose on Hardcopy output

If area dose product meter is present, (Diamentor) con-
figure yes. Otherwise configure No.

•

Perform IQ quick test.

Summary of Contents for SIREMOBIL Iso-C

































































































































Reviews:

No comments