manualshive.com logo in svg

Siemens SIREMOBIL Iso-C, Service Instructions Manual, Page: 117 / 128

Share
Download
Siemens SIREMOBIL Iso-C Service Instructions Manual Download Page 117

Brakes / Movements

7 - 3

Siemens AG

 

SPR2-230.061.01

Page 3 of 10

SIREMOBIL Iso-C

Medical Solutions

Rev. 13

12.04

CS PS 24

System Manual

 

Angulation brake magnet

•

Remove the cover of the horizontal carriage. Refer to chapter 1: Installation / removal of 
covers with brake switches on the horizontal carriage.

•

Remove the back cover with the handle for the horizontal lift movement after removing 
the 4 countersunk screws. The angulation brake magnet is now visible.

•

Remove the cover plate over the C-arm cable guide.

•

Remove the three attachment screws and remove the brake magnet. 

•

Remove the plug connection for the brake magnet and insert the new brake magnet.

•

Place the new brake magnet back on the shaft and attach it with the three screws.

•

Reattach the cable with cable ties.

•

Reattach the cover over the C-arm cable guide.

•

Reinstall the cover. Make sure the protective conductor is connected properly.

•

Perform a function test of the brake. Refer to: Brake force / Brake torque.

Fig. 3

Risk of burn!
See Chapter 1, Safety Information.

When the angulation brake is released, the brake magnet heats 
up. Be sure to switch off the power supply and let the brake mag-
net cool off before touching it.

Remove both parts of the brake magnet!

CAUTION

NOTE

Summary of Contents for SIREMOBIL Iso-C

































































































































Reviews:

No comments