manualshive.com logo in svg

Siemens SIREMOBIL Iso-C, Service Instructions Manual, Page: 120 / 128

Share
Download
Siemens SIREMOBIL Iso-C Service Instructions Manual Download Page 120

SIREMOBIL Iso-C

 

SPR2-230.061.01

Page 6 of 10

Siemens AG

System Manual

Rev. 13

12.04

CS PS 24

Medical Solutions

7 - 6

Brakes / Movements

 

Vertical lift motor

7

•

Remove the vertical lift magnet from the vertical lift motor (three screws).

•

Remove the attachment screws for the vertical lift motor.

•

Remove the vertical lift motor with the gears from the spindle.

•

Disconnect the wires from the frequency converter FU.

•

Route the wires of the new vertical lift motor to the frequency converter FU and connect 
them.

•

Place the new motor on the spindle. Make sure the spindle is seated correctly in the 
gears.

•

Attach the motor with the screws.

•

Install the vertical lift magnet on the vertical lift motor.

•

Return the SIREMOBIL Iso-C to the upright position.

•

Lubricate the spindle and the lifting column mounting.

•

Check the vertical lift function. Also check that the vertical lift motor switches off at the 
end positions of the vertical lifting column. (limit switches).

Fig. 6

Risk of injury!
Noncompliance can lead to medium to severe injuries and/or 
property damage.

To replace the vertical lift motor, the SIREMOBIL Iso-C must be 
placed on its side.

This requires 6 people. To prevent damage to the 
SIREMOBIL Iso-C or to the floor, we recommend using several 
wool blankets or corrugated cardboard, or other suitable floor 
covering. 

WARNING

Summary of Contents for SIREMOBIL Iso-C

































































































































Reviews:

No comments