manualshive.com logo in svg

Siemens SIREMOBIL Iso-C, Service Instructions Manual, Page: 90 / 128

Share
Download
Siemens SIREMOBIL Iso-C Service Instructions Manual Download Page 90

SIREMOBIL Iso-C

 

SPR2-230.061.01

Page 24 of 48

Siemens AG

System Manual

Rev. 13

12.04

CS PS 24

Medical Solutions

6 - 24

Replacing boards / replacing components

 

MEMOSKOP C-E

•

Replace the MEMOSKOP C-E.
The attachment screws are on the underside of the storage device.

•

Check the software status of the MEMOSKOP. Download the system software to the 
MEMOSKOP if necessary.

•

Use the MEMOSKOP Service Software to import the language file.

•

Configure the MEMOSKOP C-E for the correct video frequency and the number of moni-
tors present.
Refer to chapter 5 "MEMOSKOP C-E without Keyboard, Emulation ...", "Configuring the 
Video frequency" and "MEMOSKOP-Configuration for the number of existing monitors".

•

Configure the following parameters in Technical Setup for the MEMOSKOP:

Check the software status of the newly delivered MEMOSKOP. 
If the software status of the MEMOSKOP differs from that of the 
system, the system software status must be downloaded to the 
MEMOSKOP. 
The MEMOSKOP software status can be read out in the 2nd line 
of the User Setup. 
The first number describes the MEMOSKOP type. 
(2=CE; 3= CE-100/ C/ C & MOD; 4=C-SUB/ C-SUB & MOD).

Read and record the parameters for MEMOSKOP C-E if you are 
able to select User setup. After replacing the Memoskop, con-
figure the MEMOSKOP C-E according to the parameters recorded.

Number of Monitors

Configure 1 for SIREMOBIL with 1 monitor.
Configure 2 for SIREMOBIL with 2 monitors.

Hardcopy 

Check whether 5000 is programmed in "4 Max Hardcopy 
time". If not, program this value.

Edge 1 coef set

Check whether 3 is programmed, if not, program this value.

Edge 2 coef set

Check whether 8 is programmed, If not, program this value.

Motion detection setup

Check whether the following are programmed MD1: 
Threshold 100 and at MD2: Threshold 120. 
If not, program these values.

Date / Time format

Set to country-specific format.

Keyboard

Set to the keyboard layout being used.

Display of realtime clock

Configure Yes. Configure No only upon customer request.

Display of rotated images

Configure Yes.

Monitor zoom

Configure No.

Default LUT

Configure 2. Program a different LUT curve only upon cus-
tomer request. 

Default Edge

Configure 1. Program a different Edge enhancement value 
only upon customer request. 

Monitor split

Configure Yes.

Monitor text

Configure Yes.

NOTE

NOTE

Summary of Contents for SIREMOBIL Iso-C

































































































































Reviews:

No comments