manualshive.com logo in svg

Siemens SIREMOBIL Iso-C, Service Instructions Manual, Page: 22 / 128

Share
Download
Siemens SIREMOBIL Iso-C Service Instructions Manual Download Page 22

SIREMOBIL Iso-C

 

SPR2-230.061.01

Page 14 of 18

Siemens AG

System Manual

Rev. 13

12.04

CS PS 24

Medical Solutions

1 - 14

Prerequisites

 

SIREPHOS cover

1

•

Loosen the 4 cover screws of the surrounding C-arm housing.

•

Use a sharp knife to cut open the sealing compound all the way around the cover.

•

Lift off the C-arm cover. The 3 cover screws of the SIREPHOS cover are now accessible.

•

Remove the sealing compound residue from the C-arm cover, the SIREPHOS cover and 
the C-arm.

•

Loosen the 3 cover screws of the SIREPHOS cover.

•

Lift off the cover.

•

On completing service, place the SIREPHOS cover on the SIREPHOS.

•

Refasten the SIREPHOS cover with the 3 cover screws.

•

Re-attach the C-arm cover and seal it all around with sealing compound.

•

Use a paper towel to wipe off excess sealing compound.

•

Refasten the C-arm cover with the 4 cover screws.

The SIREPHOS is surrounded by a C-arm cover to adapt it to the 
form of the C-arm. This cover is sealed all around with a sealing 
compound (20 49 716) to prevent any contamination of the unit by 
the SIREPHOS or the C-arm.

NOTE

Summary of Contents for SIREMOBIL Iso-C

































































































































Reviews:

No comments