Siemens SIREMOBIL Iso-C Service Instructions Manual Download Page 84

Page: 84 / 128

SIREMOBIL Iso-C

SPR2-230.061.01

Page 18 of 48

Siemens AG

System Manual

Rev. 13

12.04

CS PS 24

Medical Solutions

6 - 18

Replacing boards / replacing components

VIDEOMED DC

•

Cut off the cable ties (refer to the arrow, Fig. 6) and disconnect the plugs.

•

Remove plug X1 at the Compact optics.

•

Remove the VIDEOMED DC and place it on a clean surface. Refer to: Replacing the
VIDEOMED DC.

High voltage section of the I.I. mini voltage supply

•

Remove the high voltage section of the I.I. mini voltage supply. Remove both attach-
ment screws at the C-arm flange. Refer to the arrows, Fig. 6.

•

Disconnect the anode cable from the high voltage section.

•

Remove the O-ring and the cap nut from the cable.

Compact optics

•

Remove the attachment screws of the Compact optics. If necessary, remove the retain-
er clip for the plug / cable leads as well.

•

Remove the Compact optics.

Fig. 7

When removing the Compact optics, make sure that no dust or
dirt particles contaminate the I.I. output.

Do not loosen the eccentric screws (2/Fig. 7) on the edge of the
Compact optics! These screws are used to center the Compact
optics to the I.I. output.

NOTE

Summary of Contents for SIREMOBIL Iso-C

































































































































Search results

Summary of Contents for SIREMOBIL Iso-C

Reviews:

Siemens SIREMOBIL Iso-C, Service Instructions Manual, Page: 84 / 128

Search results

Summary of Contents for SIREMOBIL Iso-C

Reviews: