manualshive.com logo in svg

Siemens SIREMOBIL Iso-C, Service Instructions Manual, Page: 64 / 128

Share
Download
Siemens SIREMOBIL Iso-C Service Instructions Manual Download Page 64

SIREMOBIL Iso-C

 

SPR2-230.061.01

Page 28 of 30

Siemens AG

System Manual

Rev. 13

12.04

CS PS 24

Medical Solutions

5 - 28

Adjustments / Programs

 

Monitor zoom

Yes: When pressing the key for MEMOSKOP - Zoom, the 
image will be displayed enlarged.
NO: The MEMOSKOP - Zoom key has no function.
For MEMOSKOP C-E set on NO. Otherwise set YES.

Monitor split

Yes: Horizontal or vertical image split possible.
No: No horizontal or vertical image split possible.
Program Yes.

Monitor text

Yes: Superimposes text.
No: No text superimposition.
For SIREMOBIL Iso-C always set on Yes.

Maximum no. of images

The number of stored images can be progemmed.
Program the value to 700 for MEMOSKOP C and to 900 for 
MEMOSKOP SUB.
For MEMOSKOP C-E 100 program the value to 100
For MEMOSKOP C-E, this parameter is not used.

Default programs chan-
geable

Default: Yes
The organ programs can be protected against changes by 
setting "No".

Default LUT

After switch-on, the programmed brightness/contrast curve 
(LUT) is selected automatically: Default: LUT 2

Default LUT for Subtraction

After switch-on, the programmed brightness/contrast surve 
(LUT) is selected automatically for the subtraction mode, 
when equipped with a MEMOSKOP C-Sub.
Default: LUT 1

Default Edge

After switch-on, the programmed edge enhancement is 
selected automatically: For MEMOSKOP SUB set on 1.

Software compatibility

Not implemented. Must be set to "No".

Unit serial number

Enter the serial number of the SIREMOBIL Iso-C when it is 
equipped with a DICOM bridge. The serial number is requi-
red to identify the images transferred. Please note that you 
have to omit the leading 0 when entering the serial number.

Disable dose rate selection 
in user Setup

This means "Yes" for SIREMOBIL Iso-C without an area 
dose product measurement device. This means "No" for a 
SIREMOBIL Iso-C with an area dose product measurement 
device.

Subtraction K-factor,
phase A

Noise suppression, phase A, is programmed in the 
SUB-mode.
Phase A: Mask acquisition.

Subtraction K-factor,
phase B

Noise suppression, phase B, is programmed in the 
SUB-mode.
Phase B: Acquisition of fill image.

Subtraction Time of phase A The time of phase A in the SUB-mode is programmed.

Phase A: Mask acquisition.

Roadmap K-factor, phase A

Noise suppression, phase A, is programmed in the road-
map mode.
Phase A: Mask acquisition.

Function:

Comments:

Summary of Contents for SIREMOBIL Iso-C

































































































































Reviews:

No comments