manualshive.com logo in svg

Siemens SIREMOBIL Iso-C, Service Instructions Manual, Page: 109 / 128

Share
Download
Siemens SIREMOBIL Iso-C Service Instructions Manual Download Page 109

Replacing boards / replacing components

6 - 43

Siemens AG

 

SPR2-230.061.01

Page 43 of 48

SIREMOBIL Iso-C

Medical Solutions

Rev. 13

12.04

CS PS 24

System Manual

 

•

Remove the two setscrews of the coupling unit (1/Fig. 20) shows the length of the left 
setscrew. Also remove the right setscrew (not shown).

•

Remove the coupling unit from the centering disk.

•

Take the toothed belt off the pulley.

•

Place the new belt on the pulley.

•

Place the coupling unit back on the centering disk, ensuring that the shaft engages in the 
intermediate piece. 

•

Press the coupling unit against the centering disk and screw it back on with the two set-
screws (1/Fig. 20).

•

Reinstall the mounting plate incl. motor. In doing so, place the toothed belt on the pulley 
again, ensuring that the actual value potentiometer and its pulley are not damaged or 
bent. Reconnect the motor and incremental encoder.

•

Reattch the two lateral brackets (2/Fig. 19). For guidance first insert the top two screws 
(1/Fig. 19), but do not yet tighten them completely. Tighten the lateral screws first, then 
tighten the top two screws (2/Fig. 19).

•

Tension the toothed belt of the orbital drive again (1/Fig. 17). When depressed by thumb 
pressure on the opposite side, the belt should give approx. 2 to 3 mm.

•

Perform the mechanical settings according to the Startup Instructions, Chapter 6.

Summary of Contents for SIREMOBIL Iso-C

































































































































Reviews:

No comments