manualshive.com logo in svg

Siemens SIREMOBIL Iso-C, Service Instructions Manual, Page: 115 / 128

Share
Download
Siemens SIREMOBIL Iso-C Service Instructions Manual Download Page 115

7 - 1

Siemens AG

 

SPR2-230.061.01

Page 1 of 10

SIREMOBIL Iso-C

Medical Solutions

Rev. 13

12.04

CS PS 24

System Manual

 

Brakes / Movements

7

Brake force / Brake torque

7

Measuring the horizontal force required for movement

7

The attachment point for the spring scale is the end of the railing near the image intensi-
fier in sector B and/or the handgrip of the horizontal carriage. The carriage must always 
be pulled with a consistent speed.

¹

The maximum force for moving the horizontal carriage consistently when the 
brakes are released is 80 N.

¹

When the brakes are applied, the force must be > 180 N.

Measuring the horizontal swivel force

7

¹

Swivel force when the brakes are released max. 35 Nm.

¹

Swivel force when brakes are applied > 100 Nm. 

Fig. 1

Risk of injuries on mechanical parts!
If not observed, slight to medium injuries, especially to the hands, 
can occur.

Observe the notes concerning the C-arm carbon fiber structure.

Measurement A-C: At the handgrip of the horizontal unit, the measuring 

points move to 30, 170 and 200 mm

Measurement C-A: At the railing near the image intensifier, the measur-

ing points move to 30, 170 and 200 mm

A B C

Attachment points - spring scale

WARNING

Summary of Contents for SIREMOBIL Iso-C

































































































































Reviews:

No comments