manualshive.com logo in svg

Siemens SIREMOBIL Iso-C, Service Instructions Manual, Page: 96 / 128

Share
Download
Siemens SIREMOBIL Iso-C Service Instructions Manual Download Page 96

SIREMOBIL Iso-C

 

SPR2-230.061.01

Page 30 of 48

Siemens AG

System Manual

Rev. 13

12.04

CS PS 24

Medical Solutions

6 - 30

Replacing boards / replacing components

 

•

Configure the following parameters in User setup for MEMOSKOP:

Disable doserate selection 
in user setup

Set to "No" when equipped with an area dose product mea-
surement device. The menu "Storage of Dose on disk" and 
the menu "Dose on Hardcopy output" in User Setup are visi-
ble. Otherwise set to "Yes".

Unit serial number

Program the serial number of the SIREMOBIL.
Do not enter the leading zero. 

Default LUT

Configure 2. Only upon customers request program a 
different LUT curve.

Default Edge

Configure 1. Only upon customers request program a 
different Edge enhancement value.

Software backward com-
patible

Configure No.

Product name

Program "SIREMOBIL Iso-C".

Default program change-
able

Default: Yes.
Depending on country specific regulations configure Yes or 
No.

Create external disk

If the option "3D Reconstruction" or the option 
"DICOM Bridge" is installed or a MOD drive is present, con-
figure Yes. Otherwise configure No.

Enable Bridge

If the option "3D Reconstruction" or the option 
"DICOM Bridge" is installed or a MOD drive is present, con-
figure Yes. Otherwise configure No.

Delay 3D-PC/ DICOM 
Bridge

Only available of if option "3D Reconstruction" is installed. 
Configure 120.

Interface to 3D-PC

Only available if option "3D Reconstruction" is installed.
Configure yes.

Operating mode Para-
meters

Change the programmed parameters only upon customer 
request.

VCR output

Configure to monitor A.

Hardcopy Release

For SIREMOBIL with 1 monitor: configure to monitor A.
For SIREMOBIL with 2 monitors: Configure to monitor B.

Text monitor

For SIREMOBIL with 1 monitor: configure to monitor A.
For SIREMOBIL with 2 monitors:
Configure to both monitors.

Split screen

Configure horizontally. Configure vertically only upon cus-
tomer request.

Display of time

Configure Yes.

Set Date Time

Set the current date and time.

Hospital Name

Program the hospital name.

Storage of Dose on disk

If area dose product meter is present, (Diamentor) 
configure Yes. Otherwise configure No.

Summary of Contents for SIREMOBIL Iso-C

































































































































Reviews:

No comments