manualshive.com logo in svg

Siemens 300 Series, User Manual, Page: 54 / 197

Share
Download
Siemens 300 Series User Manual Download Page 54

2–16

ROLMphone 300/600 User Guide

Muting the Speakerphone

If you have a Mute key, you can press it to turn off the 
microphone, so that you can carry on a conversation 
in your room that the other party on your line cannot 
hear.

Mute is also helpful when someone puts you on hold, 
since it lets you hear your party reconnect even if 
there is a high noise level in your room.

To mute the 
speakerphone

➩

During your conversation, press the MUTE 
key.

The status light next to the MUTE key blinks to 
remind you that Mute is active.

To cancel

➩

Press the MUTE key or lift the handset.

Open Listening

If you have a speakerphone, you may use your hand-
set and, at the same time, let someone nearby listen to 
the conversation over the speaker. This feature is 
called Open Listening. While Open Listening is 
active, someone nearby can hear your conversation, 
but whatever they say will not be picked up by the 
speakerphone.

To use Open 
Listening during 
a handset call

➩

During your conversation, press the SPEAKER 
key.

To use Open 
Listening during 
a speakerphone 
call

➩

During your conversation, lift the handset and 
press the SPEAKER key.

To cancel

➩

Press the SPEAKER key again.

Summary of Contents for 300 Series






































































































































































































Reviews:

No comments