Siemens 300 Series User Manual Download

Page: 35 / 197

Introduction

1–21

1. Int

rod
uction

Tones, cont.

Intrusion tone followed
by a ringing-beep tone

The party you called is on the
phone, but has received a call
waiting indication. Stay on the
phone until the party answers.

Long tone, followed by
an intrusion tone
repeated every 8 secs.

Busy override and speaker call
intrusion reminder

1-sec. tone after dialing

There is a short queue for an
outgoing trunk.

Ringing (ringback)
tone

The phone you called is ringing.

Short tone every 20 sec.

Internal call waiting

Single (conference)
tone

A new party has been added to a
conference.

Steady high tone

A technician is testing your
phone.

3 short tones (confirma-
tion tone)

A feature has been successfully
activated.

3 short tones followed
by dial tone

Additional input, such as a PIN,
is required.

30-sec. tone after
dialing

There is a long queue for an
outgoing trunk.

2 short tones every 20
secs.

External call waiting

Very short tone after
dialing

You have been routed to the next
outgoing trunk or to a more
expensive route.

Wavering (error) tone

Invalid feature request

Sound

Meaning

Summary of Contents for 300 Series






































































































































































































Search results

Summary of Contents for 300 Series

Reviews:

Related manuals for 300 Series

Brands by name

Popular brands

Siemens 300 Series, User Manual

Search results

Summary of Contents for 300 Series

Reviews:

Related manuals for 300 Series

Brands by name

Popular brands