Siemens 1PH818 Operating Instructions & Installation Instructions Download Page 115 | Manualshive

Page: 115 / 198

background image

Assembly

● Push the protecting ring over the end of the shaft.
● For 1PH818. or 1PH822. motors, ensure that the outer collar is placed with a space of 1 mm

from the bearing end shield (detail Z).

ཱ

=

PP

=

Figure 9-2

Fitting the protecting ring

WARNING

Lifting using the cooling water pipes
The cooling water pipe system has not been designed so that it can be used to lift the motor.

The machine can fall when lifted. Death, serious injury, or material damage will result.
● Only use the eyebolts on the bearing shields to transport and lift the motor.

9.3.3

Removing and mounting the external fan

WARNING

Live parts
Contact with live parts can cause death, serious injury or material damage.
1. Before carrying out any maintenance work on the device, disconnect it from the line supply,

particularly before opening the terminal box.

2. Make sure that the device cannot be switched back on.

Maintenance

9.3 Repair

SIMOTICS M-1PH8 1PH818., 1PH822.

Operating Instructions 07/2016

115

«
...
113
114
115
116
117
...
»

Summary of Contents for 1PH818







































































































































































































Reviews:

No comments

Related manuals for 1PH818

Brand: SAESHIN Pages: 2

Brand: Kohler Pages: 116

Brand: TAARKS Pages: 7

Brand: Nord Drivesystems Pages: 112

Brand: Landa Pages: 64

Brand: Nice Pages: 21

Era-Era Zero E LH

Brand: Nice Pages: 32

Brand: Hatz Pages: 94

Brand: FUTABA Pages: 2

Brand: Wilesco Pages: 4

Brand: O.S. engine Pages: 30

Brand: Hotsy Pages: 68

ARO AF1060 Series

Brand: Ingersoll-Rand Pages: 8

Brand: Ingersoll-Rand Pages: 8

Brand: Ingersoll-Rand Pages: 8

Brand: Ingersoll-Rand Pages: 8

Brand: Mitsubishi Pages: 116

Brand: Briggs & Stratton Pages: 100

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands