manualshive.com logo in svg

Siemens 1PH818, Operating Instructions & Installation Instructions

Share
Download
Siemens 1PH818 Operating Instructions & Installation Instructions Download Page 24

Underwriters Laboratories
The SIMOTICS motor series generally complies with UL and cUL requirements as component 

of motor applications - and is correspondingly listed. Specifically developed motors and 

functions are the exceptions in this case. Here, it is important that you carefully observe the 

contents of the quotation and that there is a cUL mark on the rating plate (nameplate)!

Quality management system
Siemens AG employs a quality management system that meets the requirements of ISO 9001 

and ISO 14001.

Certificates that can be downloaded
You can download certificates for the SIMOTICS motor series at the following link:
Certificates (

https://support.industry.siemens.com/cs/ww/en/ps/13358/cert

)

Drive 

The motor speed is controlled using a converter. 

NOTICE
Destruction of the machine when operated directly from the line supply 
The machine will be destroyed if it is directly connected to the line supply. Only operate the 

machine using a converter.   

Types of construction

The motor is available in the following basic types of construction and further optional types 

of construction with additional application possibilities. 

Table 3-3

Types of construction

Basic types of construction

Other applications in construction type

IM B3

IM B6, IM B7, IM B8, IM V6

IM V15

-

IM V5

-

IM B35

IM B5, IM V3, IM V35

The machine is supplied with two assembled lifting eyes. For IM V5 and IM V15 types of 

construction with "shaft extension pointing downward", the machine is equipped with two 

additional Vario eye bolts. 

Description

SIMOTICS M-1PH8  1PH818., 1PH822.

24

Operating Instructions 07/2016

Summary of Contents for 1PH818







































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands