Siemens 1PH818 Operating Instructions & Installation Instructions Download Page 39 | Manualshive

Page: 39 / 198

background image

Rotor shipping brace

Machines ordered with the "Increased radial force" option are equipped with cylindrical-roller

bearings and a rotor shipping brace.

NOTICE
Transport damage if the rotor shipping brace device is not used.
The motor can be damaged if it is jolted during transport. This can result in material damage.
● Always transport the motor with the rotor shipping brace supplied. The rotor shipping brace

must be attached during transportation.

● Only remove it before pushing on the drive element.
● If you transport the machine after the output transmission element has been pulled on,

then you must axially fix the rotor in another way.

཰

཰

ཱ

①

Sleeve

②

Shaft screw

Figure 4-5

Rotor shipping brace

Table 4-3

Tightening torque and preloading force for axially fixing the rotor

Type

Thread in the shaft end Tightening torque

Preload

1PH818.

M20

50 Nm

12 kN

1PH822.

M20

50 Nm

12 kN

1PH828.

M24

100 Nm

20 kN

WARNING

Lifting using the cooling water pipes
The cooling water pipe system has not been designed so that it can be used to lift the motor.

The machine can fall when lifted. Death, serious injury, or material damage will result.
● Only use the eyebolts on the bearing shields to transport and lift the motor.

Preparations for use

4.13 Transport and storage

SIMOTICS M-1PH8 1PH818., 1PH822.

Operating Instructions 07/2016

39

«
...
37
38
39
40
41
...
»

Summary of Contents for 1PH818







































































































































































































Reviews:

No comments

Related manuals for 1PH818

Brand: Hatz Diesel Pages: 56

Brand: Kubota Pages: 285

HOME MOTION Roll Up 28 WT

Brand: SOMFY Pages: 10

Brand: Sachs Pages: 42

Brand: Perkins Pages: 128

Brand: Mercedes-Benz Pages: 324

Brand: Viessmann Pages: 14

SW Brushless Series

Brand: Swiwin Pages: 14

Brand: Dietz Pages: 10

Brand: Dietz Pages: 11

Brand: Volvo Penta Pages: 61

Brand: Volvo Penta Pages: 92

Brand: Volvo Penta Pages: 216

Brand: Ibi Pages: 2

Brand: STEYR Pages: 118

Brand: LinMot Pages: 24

Brand: LinMot Pages: 30

Brand: Continental Refrigerator Pages: 146

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands