Siemens 1PH818 Operating Instructions & Installation Instructions Download Page 97

Page: 97 / 198

8.10.2

Electrical faults at force-ventilated motors

Note
When operating the machine with a converter, also refer to the operating instructions of the

frequency converter if electrical faults occur.

Table 8-1

Electrical faults

↓ Motor fails to start

↓ Motor accelerates sluggishly

↓ Humming noise when starting

↓ Humming noise in operation

↓ High temperature rise under load

↓ High temperature rise of individual winding sections

Possible causes of faults

Remedial measures

Rotor (partially) demagnetized

Contact the Service Center.

Overload

Reduce the load.

Interruption of a phase in the

feeder cable

Check the frequency converters and feeder cables.

Interrupted phase in the feeder

cable after switching on

Check the frequency converters and feeder cables.

X Winding short circuit or inter-

phase short circuit in stator wind‐

ing

Determine the winding resistances and insulation resistan‐

ces. Contact the Service Center.

Converter output voltage too

high, frequency too low

Check the settings at the frequency converter and perform

the automatic motor identification.

External fan is not running

Check the external fan and its connections.

Reduced air intake

Check the air ducts; clean the machine.

8.10.3

Electrical faults at water-cooled motors

Note
When operating the machine with a converter, also refer to the operating instructions of the

frequency converter if electrical faults occur.

Operation

8.10 Faults

SIMOTICS M-1PH8 1PH818., 1PH822.

Operating Instructions 07/2016

Summary of Contents for 1PH818







































































































































































































Search results

Summary of Contents for 1PH818

Reviews:

Related manuals for 1PH818

Brands by name

Popular brands

Siemens 1PH818, Operating Instructions & Installation Instructions

Search results

Summary of Contents for 1PH818

Reviews:

Related manuals for 1PH818

Brands by name

Popular brands