manualshive.com logo in svg

Siemens 1PH818, Operating Instructions & Installation Instructions

Share
Download
Siemens 1PH818 Operating Instructions & Installation Instructions Download Page 112

9.2.6.7

Servicing the external fan

● Check the external fan every 12 months for mechanical vibration as specified in DIN ISO 

10816. The maximum permissible vibrational severity is 2.8 mm/s measured on the end 

shield of the impeller-side motor bearing.

● Regularly clean and inspect the fan. Impeller and frame are subject to natural wear 

depending on the area of application and displacement medium.

WARNING

Impeller can crack
Due to deposits and the resulting imbalance there is a hazard of fatigue fracture of the 

impeller. The impeller can crack in operation. Death, serious injury, or material damage 

can result. 
● Regularly clean and inspect the fan.

WARNING

Voltages at the internal motor connections
The motor may continue running, e.g. due to airflow, or may run on after being shut down. 

This means that dangerous voltages of over 50 V can occur at the internal motor 

connections. Death, serious injury, or material damage can result.
● For safety reasons, it is not permissible to make any unauthorized modifications or 

changes to the fan.

● The external fan can automatically switch on and switch off as a result of its inherent 

function.

● After a power failure or when the power has been disconnected, the external fan starts 

up automatically again when the voltage is restored.

● Wait until the external fan has come to a standstill before approaching it.
● Provide a protective circuit that prevents the main motor from being switched on when 

the external fan is not in operation.

Clean the external fan

WARNING

Danger of shearing
Death, severe injury and material damage can occur if you come into contact with the rotating 

fan impeller. 
● The fan impeller must be stationary when carrying out any work on the external cooling 

system. 

● Interrupt/disconnect the external cooling unit circuit. 
● Lock out the circuit so that it cannot be switched on again.

Maintenance
9.2 Inspection and maintenance

SIMOTICS M-1PH8  1PH818., 1PH822.

112

Operating Instructions 07/2016

Summary of Contents for 1PH818







































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands