manualshive.com logo in svg

Siemens 1PH818, Operating Instructions & Installation Instructions

Share
Download
Siemens 1PH818 Operating Instructions & Installation Instructions Download Page 36

4.13

Transport and storage

When carrying out any work on the machine, observe the general safety instructions 

(Page 13) and the specifications contained in EN 50110‑1 regarding safe operation of electrical 

equipment.

4.13.1

Checking the delivery

Checking the delivery for completeness

The drive systems are put together on an individual basis. When you take receipt of the 

delivery, please check immediately whether the items delivered are in accordance with the 

accompanying documents. Siemens will not accept any claims relating to items missing from 

the delivery and which are submitted at a later date.
● Report any apparent transport damage to the delivery agent immediately. Never 

commission a damaged motor.

● Report any apparent defects/missing components to the appropriate Siemens office 

immediately.

These safety instructions are part of the scope of supply; keep them in a location where they 

can be easily accessed. 

4.13.2

Lifting and transportation

To safely lift and transport the machine, the following requirements must be met: 
● Personnel operating cranes and fork-lift trucks must be appropriately qualified.
● If the motor is packed, depending on the weight, size and on-site conditions, lift crates and 

transport frames using a fork-lift truck or a crane with slings. Use a crane or fork-lift truck 

suitable for the load.

● When lifting the machine, use only approved and undamaged sling guides and spreaders 

of sufficient rated capacity. Check the lifting equipment prior to its use. The weight of the 

machine is shown on the rating plate.

● When lifting the machine, refer to the information on the lifting plate.

– Comply with the specified spreading angles.
– Do not exceed the maximum lifting acceleration and lifting speed specified on the lifting 

plate. Lift the machine without jerking it.

Acceleration a ≤ 0.4 g (≈ 4 m/s

2 

)

Velocity v ≤ 20 m/min

● Use only the load carrying device on the stator frame for lifting.

Preparations for use
4.13 Transport and storage

SIMOTICS M-1PH8  1PH818., 1PH822.

36

Operating Instructions 07/2016

Summary of Contents for 1PH818







































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands