Siemens 1PH818 Operating Instructions & Installation Instructions Download Page 70

Page: 70 / 198

6.3.3

Laying cables

● Lay the cables in accordance with IEC/EN 60364-5-52.
● Use EMC cable glands for fixed cables. Screw the EMC cable glands into the threaded

holes in the entry plate, which can be unscrewed.

● Use shielded cables whose shields are conductively connected to a large area of the

terminal box of the motor via EMC cable glands.

● In the case of aluminum connecting bars, insert a steel washer between the cable lug and

the connecting bar. This prevents contact corrosion.

● Arrange the exposed connecting cables in the terminal box so that the PE conductor has

excess length and the insulation of the cable strands cannot be damaged.

● Close off unused bushings with a metal threaded plug. This is the way to achieve a high

frequency-proof shielding.

6.3.4

Electrical connection data

Cable entry and technical connection data depend on the mounted terminal box. You can find

more information on the terminal box that is mounted in the ordering documentation or in the

catalog.

1XB7 322

1XB7 422

Electrical connection
6.3 Connecting

SIMOTICS M-1PH8 1PH818., 1PH822.

Operating Instructions 07/2016

Summary of Contents for 1PH818







































































































































































































Search results

Summary of Contents for 1PH818

Reviews:

Related manuals for 1PH818

Brands by name

Popular brands

Siemens 1PH818, Operating Instructions & Installation Instructions

Search results

Summary of Contents for 1PH818

Reviews:

Related manuals for 1PH818

Brands by name

Popular brands