Siemens 1PH818 Operating Instructions & Installation Instructions Download Page 116

Page: 116 / 198

Removing and mounting the external fan

1. Before carrying out any maintenance work on the device, disconnect it from the line supply.
2. Unscrew the screws

①

and remove the external fan.

3. For mounting, proceed in reverse order.

Figure 9-3

Unscrewing the external fan (1PH818., 1PH822.)

9.3.4

Connecting the speed encoder

NOTICE
Electrostatic discharge
Electronic modules contain components that can be seriously damaged by electrostatic

discharge. These modules can easily be destroyed unless they are handled properly.
To protect your equipment against damage, follow the instructions given in the section headed

"Electrostatic Sensitive Devices" (Page 18).

Maintenance
9.3 Repair

SIMOTICS M-1PH8 1PH818., 1PH822.

116

Operating Instructions 07/2016

Summary of Contents for 1PH818







































































































































































































Search results

Summary of Contents for 1PH818

Reviews:

Related manuals for 1PH818

Brands by name

Popular brands

Siemens 1PH818, Operating Instructions & Installation Instructions

Search results

Summary of Contents for 1PH818

Reviews:

Related manuals for 1PH818

Brands by name

Popular brands