manualshive.com logo in svg

Siemens 1PH818, Operating Instructions & Installation Instructions

Share
Download
Siemens 1PH818 Operating Instructions & Installation Instructions Download Page 117

1. Insert the connector into the socket.
2. Press the cable into the holder provided for it.
3. Screw on the sensor cover. Take care that you do not catch the cable as you screw it in.

཰

཰

ཱ

ི

Figure 9-4

Electrical connection of the speed sensor 

Note
Replacing or adjusting the speed encoder
Replacing or adjusting the speed encoder in an incorrect manner can result in machine 

malfunctions. Arrange to have the speed encoder replaced or adjusted by Siemens service 

personnel. This will ensure problem-free functioning.

9.3.5

Replacing the DRIVE-CLiQ interface (encoder module)

Only trained Siemens service engineers (Page 131) are authorized to replace the DRIVE-CLiQ 

interface (sensor module).  

NOTICE
Electrostatic discharge
Electronic modules contain components that can be destroyed by electrostatic discharge. 

These modules can be easily destroyed by improper handling.
To protect your equipment against damage, follow the instructions given in the chapter ESD 

Guidelines (Page 18).

Maintenance

9.3 Repair

SIMOTICS M-1PH8  1PH818., 1PH822.

Operating Instructions 07/2016

117

Summary of Contents for 1PH818







































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands