manualshive.com logo in svg

Siemens 1PH818, Operating Instructions & Installation Instructions

Share
Download
Siemens 1PH818 Operating Instructions & Installation Instructions Download Page 57

● When lifting the machine, refer to the information on the lifting plate.

– Comply with the specified spreading angles.
– Do not exceed the maximum lifting acceleration and lifting speed specified on the lifting 

plate. Lift the machine without jerking it.

Acceleration a ≤ 0.4 g (≈ 4 m/s

2 

)

Velocity v ≤ 20 m/min

● Use only the load carrying device on the stator frame for lifting.

WARNING

Transport for a different type of construction
If you do not transport or lift the machine in a position appropriate for its construction, the 

machine can tip, slip into the lifting equipment or fall down. This can result in death, serious 

injury or material damage.
● Use only the load carrying device on the stator frame for lifting.
● Use the load carrying device appropriate for the machine position.  
● Use suitable rope guiding or spreading devices. The weight of the machine is shown on 

the rating plate.

WARNING

Transport if the center of gravity is not at the center.
If the center of gravity of a load is not located centrally between the attachment points, the 

motor can tip over or slip out of the lifting equipment and fall when it is being transported or 

lifted. This can result in death, serious injury or material damage.
● Comply with the handling instructions on the machine when transporting it.
● Be aware of the possibility of different loads on the sling ropes or lifting straps and the 

carrying capacity of the lifting equipment.

● Always take account of the center of gravity when transporting or lifting the motor. If the 

center of gravity is not located centrally between the attachment points, then position the 

hoisting hook above the center of gravity. 

Note
Place the machine in a secure and raised position
In order to obtain easy and safe access to the underside of the machine, place it in a secure 

and raised position.

DANGER

Standing under suspended loads
If the lifting gear or load handling attachments were to fail, the machine could fall. This can 

result in death, serious injury or material damage. 
Never remain under or in the immediate vicinity of the machine when it is raised.

Mounting

5.2 Lift the machine to where it will be mounted and position it

SIMOTICS M-1PH8  1PH818., 1PH822.

Operating Instructions 07/2016

57

Summary of Contents for 1PH818







































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands