Siemens 1PH818 Operating Instructions & Installation Instructions Download Page 67

Page: 67 / 198

Electrical connection

When carrying out any work on the machine, observe the general safety instructions

(Page 13) and the specifications contained in EN 50110‑1 regarding safe operation of electrical

equipment.

Note
Service Center
If you require support when electrically connecting up the machine, please contact the Service

Center (Page 131).

6.1

Safety instructions relating to the electrical connection

NOTICE
Connected parts can loosen
If you use fixing elements made from the wrong material or apply the wrong tightening torque,

this could impair current transfer or cause connecting parts to become loose. This could result

in material damage to the machine or even in total failure, which could in turn lead indirectly

to material damage to the system.
● Tighten the screwed connections to the specified tightening torques.
● Observe any specifications regarding the materials from which fixing elements must be

made.

● When performing servicing, check the fastenings.

Summary of Contents for 1PH818







































































































































































































Search results

Summary of Contents for 1PH818

Reviews:

Brands by name

Popular brands

Siemens 1PH818, Operating Instructions & Installation Instructions

Search results

Summary of Contents for 1PH818

Reviews:

Brands by name

Popular brands