Siemens 1PH818 Operating Instructions & Installation Instructions Download Page 30

Page: 30 / 198

Constituent

Value

Operating pressure

6 bar max.

Inlet temperature

< 30°C

Minimum cooling water inlet temperature

cooling water

> T

ambient

- 5 K

Anti-freeze protection / corrosion protection

20 … 30 %

Inhibitor NALCO 00GE056

0.2 … 0,25 %

Inlet temperature of the cooling water

The maximum cooling water inlet temperature is30 °C.

NOTICE
Inlet temperature of the cooling water
If the minimum inlet temperature of the cooling water cannot be maintained or reached, this

may result in condensation forming on the machine.
Adopt appropriate measures to achieve the inlet temperature of the cooling water.

Alternatively, you can dry the ambient air.

4.4

Ensuring cooling

Note
Note also the technical data on the rating plates on the motor enclosure.

Preconditions for adequate cooling

● For motors that are cooled by the ambient air, the cooling air must be able to flow unimpeded

to and from the motors. Hot discharged air should not be drawn in again.

NOTICE
Overheating
If the required cooling air flow cannot be maintained, the machine can overheat. This can

result in material damage.
● Maintain the required minimum clearance for customer-supplied mounted accessories

at the air intake opening and at the air discharge openings to ensure the required

cooling air flow.

● Comply with the conditions of the IP degree of protection.

More stringent requirements regarding the IP degree of protection may necessitate the

installation of suitable filters and special arrangement of the intake and outlet openings.

● Equipment and cables must be connected without strain.

Preparations for use
4.4 Ensuring cooling

SIMOTICS M-1PH8 1PH818., 1PH822.

Operating Instructions 07/2016

Summary of Contents for 1PH818







































































































































































































Search results

Summary of Contents for 1PH818

Reviews:

Related manuals for 1PH818

Brands by name

Popular brands

Siemens 1PH818, Operating Instructions & Installation Instructions

Search results

Summary of Contents for 1PH818

Reviews:

Related manuals for 1PH818

Brands by name

Popular brands