Siemens 1PH818 Operating Instructions & Installation Instructions Download Page 58

Page: 58 / 198

5.2.6

Open the condensation water drain holes (water-cooled motor)

In the bearing shields at the DE and NDE, a water drain hole

①

is situated in the foot area

and another opposite the regreasing device.

Figure 5-2

Water drain holes

● Make sure that the condensation can always drain away freely.
● The plug that has been inserted into the water drain holes allows the condensation to drain

away. Do not remove the plug, otherwise the machine's degree of protection will be affected.

● If you have any questions, contact the Siemens Service Center (Page 131).

NOTICE
Damage caused by condensation
If the stator winding is damp, its insulation resistance is reduced. This results in voltage

flashovers, which can destroy the winding. Condensation can also cause rusting inside

the machine. Make sure that the condensation can always drain away freely.

Mounting
5.2 Lift the machine to where it will be mounted and position it

SIMOTICS M-1PH8 1PH818., 1PH822.

Operating Instructions 07/2016

Summary of Contents for 1PH818







































































































































































































Search results

Summary of Contents for 1PH818

Reviews:

Related manuals for 1PH818

Brands by name

Popular brands

Siemens 1PH818, Operating Instructions & Installation Instructions

Search results

Summary of Contents for 1PH818

Reviews:

Related manuals for 1PH818

Brands by name

Popular brands