manualshive.com logo in svg

Siemens 1PH818, Operating Instructions & Installation Instructions

Share
Download
Siemens 1PH818 Operating Instructions & Installation Instructions Download Page 64

Alignment accuracy  

Note
Alignment accuracy
Remember to take account of data concerning the alignment accuracy of the driven load and 

the coupling.

1. Align the motors with coupling output in such a manner that the center lines of the shafts 

are parallel with no offset. This ensures that no additional forces affect their bearings during 

operation.

2. Perform the fine adjustments with plates under the entire motor foot.

š'

[

\

Figure 5-5

Aligning the motor

Table 5-4

Permissible deviations when aligning the motor

Permissible deviations

Radial shaft offset [x]

Axial shaft offset [y]

Flexible coupling

0.05 mm

0.05 mm

Mounting
5.3 Installing the machine

SIMOTICS M-1PH8  1PH818., 1PH822.

64

Operating Instructions 07/2016

Summary of Contents for 1PH818







































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands