manualshive.com logo in svg

Sharp AR-BC260, Operation Manual, Page: 65 / 184

Share
Download
Sharp AR-BC260 Operation Manual Download Page 65

LARGE CAPACITY TRAY

3-17

3

Misfeed in the large capacity tray

When a misfeed occurs in the large capacity tray, remove the misfed paper, following the procedure below.

1

While holding the tray release lever,
carefully slide the large capacity tray away
from the main unit until it stops.

2

Remove any misfed paper from the main
unit and the large capacity tray.

If the misfed paper is
stuck inside the machine
and cannot be removed,
open the side cover and
then remove the misfed
paper. (See "Misfeed in
the transport area,
fusing area, and exit
area" on page 2-20.)

3

Open the top cover.

4

Remove the misfed paper.

Be sure not to tear the
misfed paper during
removal.
After removing the
misfed paper, close the
top cover.

5

Push the large capacity tray towards the
main unit and latch it into place.

Gently push the large
capacity tray back in
until it stops.

6

If misfed paper is not found in step 2, pull
the tray out.

7

Remove the misfed paper.

8

Gently push the tray back into place.

The paper feed table
automatically rises to the
paper feed position.
Make sure that the
paper misfeed screen is
cleared and the normal
message screen
appears.

Release lever

Upper right
side cover

ApollonII_general-copy_SEC.book  17 

ページ

  

２００４年９月６日　月曜日　午後４時５７分

Summary of Contents for AR-BC260

























































































































































































Reviews:

No comments