manualshive.com logo in svg

Sharp AR-BC260, Operation Manual, Page: 61 / 184

Share
Download
Sharp AR-BC260 Operation Manual Download Page 61

SADDLE STITCH FINISHER

3-13

3

Stapling position quick reference guide for duplex output

The orientation of the copy paper, original, scanned original data, and binding position selection are all interrelated.
The table below shows these relationships.

Orientation of original or original data

Output result

Page 1

Page 2

Page 1 & Page 2

Duplexed

One-position stapling

Two-position stapling

One-position stapling

Two-position stapling

One-position stapling

Two-position stapling

Two-position stapling

One-position stapling

One-position stapling

One-position stapling

Left binding with two-position 
stapling is not possible.

Right binding with two-
position stapling is not 
possible.

Top binding with two-position 
stapling is not possible.

Two-position stapling along 
the shorter edge is not 
possible.

Two-position stapling along 
the shorter edge is not 
possible.

Two-position stapling along 
the shorter edge is not 
possible.

Right binding

Right binding

T

op binding

T

op binding

Left binding

Left binding

P

o

rtrait orientation printing

Landscape orientation printing

ApollonII_general-copy_SEC.book  13 

ページ

  

２００４年９月６日　月曜日　午後４時５７分

Summary of Contents for AR-BC260

























































































































































































Reviews:

No comments