Sharp AR-BC260 Operation Manual Download Page 38

Page: 38 / 184

REPLACING THE TONER CARTRIDGES

2-16

Remove the protective material from the
new toner cartridge.

Insert the new toner cartridge.

Align the insert holes
as shown and then
push the cartridge in.

Push the cartridge in until it locks securely
in place.

Return the cartridge lock lever.

Close the front cover.

After the toner cartridge
is replaced, the machine
automatically enters
resolution adjustment
mode. (In some cases,
this may take about 5
minutes.)

NOTE

A toner cartridge of a different color cannot be
installed. For instance, a yellow cartridge cannot be
installed in the cyan position.

NOTE

Do not push the white
area shown in the
illustration.
The lock lever may
come down.

CAUTION

●

Do not throw the toner cartridge into a fire. Toner may fly and cause burns.

●

Store toner cartridges out of the reach of small children.

ApollonII_general-copy_SEC.book 16

ページ

２００４年９月６日　月曜日　午後４時５７分

Summary of Contents for AR-BC260

























































































































































































Search results

Summary of Contents for AR-BC260

Reviews:

Sharp AR-BC260, Operation Manual, Page: 38 / 184

Search results

Summary of Contents for AR-BC260

Reviews: