Sharp AR-BC260 Operation Manual Download Page 14

Page: 14 / 184

1-4

PART NAMES AND FUNCTIONS

Exterior

Left tray (See page 5-5)

Finished sheets are deposited here.

Left side cover

Open this cover when a paper misfeed occurs in
the fusing unit or the transfer unit.

Reversing single pass feeder

This automatically feeds originals to be scanned.
The feeder can turn the original over and scan the
back side as well as the front side for support of
two-sided originals.

Power switch

Press to turn power on and off.

Front cover

Open to replace toner cartridge.

Operation panel

Center tray (See page 5-5)

Finished sheets are deposited here.

Bypass tray

Special papers (including transparency film) and
copy paper can be fed from the bypass tray.

Stand/1 x 500 sheet paper drawer *

(See page 2-7)

Stand/3 x 500 sheet paper drawer *

(See page 2-7)

Duplex module/2 x 500 sheet paper drawer*

(See page 2-8)

Paper tray

Each tray can hold approximately 500 sheets of the
recommended paper for color (21 lbs. or 80

or approximately 500 sheets of SHARP standard
paper (21 lbs. or 80

Left side cover release

Push this release up to open the left side cover.

Duplex bypass/inverter unit and exit tray* (See

page 1-6)

and

are peripheral devices. For a description of these devices, see page 1-6.

ApollonII_general-copy_SEC.book 4

ページ

２００４年９月６日　月曜日　午後４時５７分

Summary of Contents for AR-BC260

























































































































































































Search results

Summary of Contents for AR-BC260

Reviews:

Sharp AR-BC260, Operation Manual, Page: 14 / 184

Search results

Summary of Contents for AR-BC260

Reviews: