manualshive.com logo in svg

Sharp AR-BC260, Operation Manual, Page: 42 / 184

Share
Download
Sharp AR-BC260 Operation Manual Download Page 42

MISFEED REMOVAL

2-20

Misfeed in the transport area, fusing area, and exit area

Transport area

1

Open the upper side cover and check for a
misfeed.

Push the lever upward
and gently open the
cover.

Be careful not to tear the
misfed paper during
removal.

2

Gently close the upper side cover.

Exit area

1

Misfeed in the exit area

Models with an exit tray
attached to the duplex
bypass/inverter unit:

Gently remove the misfed
paper as shown in the
illustration, taking care
not to tear the paper.

Models without the
duplex bypass/
inverter unit:

Gently remove the misfed
paper as shown in the
illustration, taking care
not to tear the paper.

Upper exit tray:

Gently remove the
misfed paper as shown
in the illustration, taking
care not to tear the
paper.

Fusing area

1

Open the duplex bypass/inverter unit.

Grasp the finger hold
and gently open the unit. 

2

Remove the misfed paper as shown in the
illustrations below.

If paper is misfed in the
transport area, turn roller
rotating knob A in the
direction of the arrow to
remove the misfed paper.

If you do not find a
misfeed, open the cover
of the fusing unit and
check for a misfeed
inside the fusing unit.

3

Misfeed in the transfer unit

If paper is misfed on the
transfer belt, remove it
gently without touching
the transfer belt. Do not
pull out the transfer unit.

4

Gently close the duplex bypass/inverter unit.

After closing, confirm that
the misfeed message
has been cleared and the
normal display appears.
If the duplex bypass/
inverter unit is not
installed, close the side
cover in the same way.

NOTE

If paper is loaded in the bypass tray, temporarily remove the
paper and close the bypass tray before opening the side cover.

NOTE

The misfeed may have occurred inside the machine.
Check carefully and remove it.

NOTE

Even after clearing a misfeed, paper may remain inside
the machine on the transfer belt where it is not visible. In
this case, after visible misfeeds are removed, the paper
on the transfer belt will be automatically moved to a
position where it is visible and a misfeed will be indicated
once again on the display. Clear the misfeed as explained
in "Misfeed in the transfer unit" (step 3 on the right side of
this page). For this reason, it may be necessary to
perform the "Misfeed in the transfer unit" procedure twice.

The fusing unit is hot. Take care in removing paper. (Do
not touch any metal parts.)

The fusing unit is hot. Take care in removing paper. (Do not
touch any metal parts.)

The transfer unit is hot. Take care in removing paper. (Do
not touch any metal parts.)

CAUTION

CAUTION

CAUTION

ApollonII_general-copy_SEC.book  20 

ページ

  

２００４年９月６日　月曜日　午後４時５７分

Summary of Contents for AR-BC260

























































































































































































Reviews:

No comments