manualshive.com logo in svg

Sharp AR-BC260, Operation Manual, Page: 58 / 184

Share
Download
Sharp AR-BC260 Operation Manual Download Page 58

SADDLE STITCH FINISHER

3-10

Misfeed in the saddle stitch finisher

When a misfeed occurs in the saddle stitch finisher, remove the misfed paper following the procedure below.

1

Unlatch the saddle stitch finisher and slide
it away from the main unit.

2

Remove the misfed paper from the main
unit.

After removing the
misfed paper, open and
close the duplex bypass/
inverter to reset the jam
indicator. ("Misfeed in
the Fusing area" step 1
or 4 on page 2-20)

3

If there was no misfed paper in step 2, pull
roller rotating knob B on the punch unit
towards you and rotate it. (Only when an
optional punch unit is installed.)

Rotating roller rotating
knob B releases the
caught paper.

4

Open the top cover.

5

Remove the misfed paper.

Remove the paper
gently, taking care not to
tear it.

6

Close the top cover.

7

Remove the misfed paper from the stapler
compiler.

Be careful not to tear the
misfed paper during
removal.

8

Open the saddle stitch section cover.

9

Remove the misfed paper.

Be careful not to tear the
misfed paper during
removal.

NOTE

The saddle stitch finisher and the machine are
connected at the rear. Exercise caution when pulling
them apart.

Roller rotating 

knob B

ApollonII_general-copy_SEC.book  10 

ページ

  

２００４年９月６日　月曜日　午後４時５７分

Summary of Contents for AR-BC260

























































































































































































Reviews:

No comments