manualshive.com logo in svg

Sharp AR-BC260, Operation Manual, Page: 44 / 184

Share
Download
Sharp AR-BC260 Operation Manual Download Page 44

MISFEED REMOVAL

2-22

Misfeed in the duplex bypass/inverter unit and duplex
module/2 x 500 sheet paper drawer

1

Perform steps 1 and 2 of "Misfeed in the
stand/1 x 500 sheet paper drawer" on the
previous page.

2

Open the upper cover of the duplex
bypass/inverter unit.

3

Remove the misfeed from the upper part of
the duplex bypass/inverter unit.

Hold the upper cover of
the unit open while
removing the misfed
paper.

4

Close the upper cover of the duplex
bypass/inverter unit.

5

Lift the exit tray if one is installed and open
the cover of the duplex bypass/inverter
unit.

6

Remove the misfed paper.

While holding the exit
tray up, remove the
misfed paper as shown
in the illustration. Be
careful not to tear the
misfed paper during
removal.

7

Close the cover of the duplex bypass/
inverter unit and return the exit tray to its
original position.

8

Remove a misfeed from the bottom of the
duplex bypass/inverter unit.

Gently remove the
misfed paper from the
bottom of the duplex
bypass/inverter unit as
shown in the illustration,
taking care not to tear
the paper.

Make sure that there is
no misfed paper in the
machine.

9

Pull out the duplex module of the duplex
module/2 x 500 sheet paper drawer.

NOTE

Paper misfed from a paper tray may be extending out of the tray into the right side cover area. In this case if the
tray is drawn out of the machine, the paper may become torn and difficult to remove. To prevent this from
happening, always open the right side cover first and remove the misfed paper if it is extending into that area.

ApollonII_general-copy_SEC.book  22 

ページ

  

２００４年９月６日　月曜日　午後４時５７分

Summary of Contents for AR-BC260

























































































































































































Reviews:

No comments