manualshive.com logo in svg

Sharp AR-BC260, Operation Manual, Page: 117 / 184

Share
Download
Sharp AR-BC260 Operation Manual Download Page 117

IMAGE EDIT MENU

6-21

6

11" x 17" (A3) Full-bleed

In other copy modes, image loss will occur along the copy edges. When the 11" x 17" (A3) FULL-BLEED function is
used, the full image of an 11" x 17" (A3) size original will be copied onto 12" x 18" (A3W) size copy paper.
The 11" x 17" (A3) FULL-BLEED function can only be used when the original is placed on the document glass. (The
reversing single pass feeder cannot be used.)
Reduction or enlargement cannot be selected with this function. If reduction or enlargement has been selected, the
copy ratio will be reset to 100% when this function is selected.
Automatic two-sided copying is not possible.

1

Touch the [11x17 FULL-BLEED] key on the
IMAGE EDIT menu screen.

The [11x17 FULL-
BLEED] key will be
highlighted to indicate
that the function is
turned on, and the full-
bleed icon (

) will

appear in the upper left
of the screen.

2

Touch the [OK] key on the IMAGE EDIT
menu screen.

Return to the SPECIAL MODES screen.

3

Touch the [OK] key on the SPECIAL
MODES screen.

Return to the main screen of copy mode.

4

Load 12" x 18" (A3W) copy paper into the
bypass tray.

Adjust the bypass guide
to 12" x 18" width before
loading the paper.
Remove any paper
remaining in the tray.
Pull out the tray
extension and wire
extension. (See page 2-
4)

5

Touch the [PAPER SELECT] key on the
touch panel and then select the paper type
in the bypass tray.

Touch the [PLAIN] key or the [HEAVY PAPER]
key.
If you touched the [HEAVY PAPER] key, touch the
[HEAVY PAPER1] key or the [HEAVY PAPER2]
key as appropriate for the weight of the paper you
loaded. (See step 3 on page 2-12.)

Original (11" x 17" (A3)) size

Copy (12" x 18" (A3W)) size

SINGLE COLOR

11x17

FULL-BLEED

MULT

ENLA

About the steps that follow

See pages 5-7 and 5-8.
Extend the copy receptacle and then begin
copying.

To cancel the 11 x 17 (A3) FULL-BLEED function,
touch the [11x17 FULL-BLEED] key again on the
IMAGE EDIT menu screen (step 1).

PLAIN

PLAIN

HEAVY PAPER

TRANSPARENCY

ENVELOPE

RECYCLED

COLOR

PLAIN

12x18

AUTO

EXPOSURE

AUTO

ORIGINAL

PAPER SELECT

100

%

COPY RATIO

READY TO COPY.

0

INTERRUPT

1. 8½x11

2. 8½x14

3. 11x17

4. 8½x11R

ApollonII_general-copy_SEC.book  21 

ページ

  

２００４年９月６日　月曜日　午後４時５７分

Summary of Contents for AR-BC260

























































































































































































Reviews:

No comments